Linux Community Magazine

Supporting the MSA1000, 1500cs & 1510i HP2-K08 Test

HP2-K08

QUESTION: 1What is a characteristic of the read-ahead caching mechanism?

A. Every I/O goes directly to the respective disk.B. The data read from the disks stays in cache until it reaches a threshold.C. Every I/O goes into the RAID controller cache and in a background operation tothe respective disk.D. The RAID controller reads more data than requested from the disks, predicting thenext read from the host that needs this additional data.

Answer: C

QUESTION: 2Which statement is true regarding a dual-path configuration with a single controller?

A. It is not supported.B. It requires Secure Path software.C. It is supported without Secure Path software.D. It requires the Redundancy Manager software.

Answer: C

QUESTION: 3What are two functions of RAID level 5? (Select two.)

A. uses only one physical disk in the array for parityB. distributes the parity onto every available disk in the arrayC. distributes two different parities onto every available disk in the arrayD. usually has the highest cost per GB of usable space because it duplicates the dataE. has moderate costs per GB because it uses the capacity of one disk for parity per array

Answer: B, E

QUESTION: 4Which Fibre Channel topology is used for host connection with a single MSA Hub 2/3? HP2-K08

A. fabricB. multipathC. dual loopD. arbitrated loop

Answer: D

QUESTION: 5Which drive type is best for holding large amounts of reference data?

A. ATAB. SCSIC. SATAD. Fibre Channel

Answer: C

QUESTION: 6What is the operational configuration limit for Secure Path 4.0c for Windows in an MSAstorage environment? (Select two.)

A. a maximum of 20 hosts per set of shared storage systems (per profile)B. a maximum of 128 hosts per set of shared storage systems (per profile)C. a maximum of 256 storage systems shared by a set of hosts (per profile)D. a maximum of 32 LUNS per target with a maximum of two paths per LUNE. a maximum of 128 LUNS per target with a maximum of two paths per LUN

Answer: B, D

QUESTION: 7How can you extend the storage capacity of a logical drive using the Array ConfigurationUtility? (Select two.)

A. Add a hot spare to the array.B. Add a new disk to the logical drive.C. Add unused space from any array to the logical drive.D. Add a new disk to the array where the logical drive resides. HP2-K08

E. Add unused space from the array where the logical drive resides.

Answer: D, E

QUESTION: 8Which statement about MSA-supported multipath software is correct?

A. The QLogic Multipath Driver is required for Linux operating systems.B. HP Secure Path is required for all MSA-supported operating systems.C. The QLogic Multipath Driver cannot be used for Linux operating systems.D. HP Secure Path and the Microsoft Multipath I/O driver (MPIO) can be used for allMSA-supported operating systems.

Answer: A

QUESTION: 9What is the Storage Management Utility?

A. a replacement for the Array Configuration UtilityB. an alternate management tool for MSA1xxx systemsC. a dedicated management tool for MSA1510i systemsD. a replacement for the MSA1510i Command Line Interface

Answer: C

QUESTION: 10Which rule applies for spare drive configuration with the Storage Management Utility fortheMSA1510i?

A. A spare disk must be the same speed as the other drives in the array.B. A spare disk can be mixed with SCSI and SATA drives in the same array.C. A spare disk must be the same size (or smaller) as the other drives in the array.D. A spare disk must be the same type (SCSI or SATA) as the other drives in the array.

Answer: D

Original Resource :

Visit HP2-K08 Link : HP2-K08 Download PDF Link : HP2-K08

iAutoblog the premier autoblogger software